screwing tongue and groove flooring

Fixing Wood Floors - Old House Journal Magazine

Unless you have rare or unusually fine flooring look for sources close to home. A local salvage house or even your own closet or attic may yield the best match. Replacing a Floorboard. Most floors in older homes are composed of individual (plank) or interlocking (tongue-and-groove) boards laid together.

Get Price

How to Repair Tongue and Groove Porch Flooring | DoItYourself.com

When you are working with tongue and groove porch flooring there are things that can go wrong with it. No matter how well you take care of your flooring it will still need to be repaired from time to time. As long as you keep up with these repairs you won’t have very many issues when it comes to actually repairing them.

Get Price

The Proper Way to Install OSB | Home Guides | SF Gate

The Proper Way to Install OSB. Oriented strand board or OSB is a sheet panel product similar to plywood made from layers of wood strands that are oriented in opposite directions. Builders use ...

Get Price

How to Reverse a Tongue & Groove Wood Floor | Home Guides ...

How to Reverse a Tongue & Groove Wood Floor. In a typical hardwood flooring installation the tongues of the boards must all face in the same direction. After nailing the tongues of one course ...

Get Price

Installation Methods Explained | The Wood Flooring Guide

Screwing down hardwood flooring. Screwing your hardwood floor is very similar to nailing it. You must have wooden floor boards or plywood so that the screw has something to attach to securely. Always use screws designed specifically for floor fitting such as Tongue-Tite screws.

Get Price

How to Lay a Real Pine Wood Floor | Home Guides | SF Gate

Choose tongue-and-groove edges as these are easy to put down and the nails won’t show. 2 Stack your wood in the room where the new floor is planned so the wood can acclimate to the moisture in ...

Get Price

Make your own flooring with 1x6 pine

Tongue and groove is still a butt joint. The more common practice is a 1/4″-3/8″ gap at the wall perimeter and a couple expansion rows using pennies or washers between rows while installing. Some even space every row when using DIY plank or plywood.

Get Price

Wood Flooring Blog - What Is Secret Screwing / Secret Nailing ...

Traditionally oak flooring was laid using the surface fixing method. This method involves nailing through the top surface of the board at even spacing into the floor joists below. Nowadays with the introduction of tongue and grooved oak boards the secret screwing / secret nailing method is the most commonly used method of fitting.

Get Price

Beginners guide to installing bamboo flooring - Bamboo Floo

Bamboo flooring must be at least 18mm thick and have a tongue and groove profile if you want to install it over joists. You have the choice of either secret nailing or secret screwing it to the joists. Start by securing the first row of bamboo flooring by either nailing or screwing into the groove of the planks.

Get Price

Joining Tongue-and-Groove Plywood - This Old House

If the tongue-and-groove joint doesn't close up the plywood might be slightly warped. Have a helper stand on the seam to align the tongue with the groove then rap the 2x4 with the sledge. Once the joint is tight drive in a couple of screws or nails to hold it then slide the 2x4 down along the edge of the plywood sheet and repeat the process.

Get Price

How to Install Prefinished Solid-Hardwood Flooring - DIY

Like unfinished hardwood floors the prefinished types typically have tongue-and-groove edges on all sides. They are available in 3/4-inch thickness as well as low-profile styles that are 5/16- to 5/8-inch thick which are a good or installing over existing flooring.

Get Price

Glued-Down Wide Pine Flooring

No tongue and groove required. Bostick's best is the glue that I like to use. Contributor D mentions that the tongue and groove has a longer life for future refinishing. I have to disagree. Tongue and groove flooring is made with a 1/4" groove that leaves 1/4" on top and 1/4" on bottom. The 3/8" square edge has more wood to sand overall.

Get Price

Methods to Silence A Squeaky Floor - Natural Handyman

Most modern wood floors are tongue and groove. To avoid cracking the tongues locate your nails no closer than 1/2 inch to the edge of the strip. You will also angle the nails slightly towards the center. To tighten down the floor drive 6d or 8d spiral flooring nails on a slight angle through the floor into the subflooring.

Get Price

Product Details

Product List