size lumber for a deck frame

How to Select Lumber for a Deck | Better Homes & Gardens

For a small deck (10x12 feet for example) determine how much lumber you'll need by counting all the pieces of each size—12-foot 2x4s 8-foot 2x6s and so on. Add 10 percent to framing quantities and 15 percent to decking to allow for waste.

Get Price

How to Build a Floating Deck - The Seven Trust

Lumber Needed (buy a shorter or longer length based on your dimensions): (8) 4 x 4 x 8 pieces of pressure treated lumber (for footer posts) (25) 2 x 6 x 10 pieces of pressure treated lumber (for interior frame) (4) 2 x 10 x 16 pieces of pressure treated lumber (for exterior frame) (23) 2 x 6 x 16 pieces of decking boards (for deck top)

Get Price

What Size Screws Should Be Used to Install Wood Decking? | Hunker

Deck Framing The rim joists of the deck are usually connected to the posts and to each other with bolts but large diameter screws called lag screws also can be used. These screws should be at least 1/2 inch in diameter if they will support the weight of the deck and the point should sink at least 1 1/2 inches into the stationary member.

Get Price

Building Decking - What Wood to Use and How to Go About ...

Local building regulations may specify the size of lumber that you should use. If you are using wooden posts the accepted sizes are 4"X4" or 6"X6". The post size depends on the projected size of the deck. The rest of the structural lumber frames may be from 2 "X 6" to 2"x 12". Note that a 2"x10" lumber is not as in but more like 1.5" x 9.5".

Get Price

Deck Framing: How to Determine Deck Framing Lumber Sizes

Joist Framing – (How to Determine Deck Framing Lumber Sizes) The rim joists are the joists that make up the outside of the frame. If the deck is fastened to a house or other building the board that fastens to the house framing is the ledger board.

Get Price

How to Build a Deck - The Seven Trust

Use double 2- x 6-inch deck boards as framing beams. Attach them within the post anchors with nails or structural screws. Attach them within the post anchors with nails or structural screws. The anchor is 3 1/2-inches wide and the beam is 3-inches thick so install a 1/2-inch-thick pressure-treated shim between the beams and one side of the ...

Get Price

What Size Nails Should You Use for Framing?

Framing out a deck is a slightly different process than framing your interior walls. You will need to consider what size nails to use for this new and different application. In fact it is typically recommended that you use deck screws over nails because they have a special coating that renders them more resistant to corrosion over time .

Get Price

Beam Span Chart Table | Decks.com

The species of lumber size of lumber and the load it carries. Fewer posts on upper level decks are typically more desirable to the occupants and this drives the use of larger framing materials for longer spans. Beam span maximums are based on a maximum anticipated live load. Building codes for residential decks only require 40 psf.

Get Price

How to Build a Deck (with 120+ Pics Diagrams Pro-Tips ...

5/4 lumber is actually finished to 1-1/16″. The type of 5/4 lumber used on decks has rounded edges and is known as “decking board”. Composite decking material is generally the same size as 5/4 lumber (or close to it). Pro-Tip: Overhead power lines must have at least 10′ of clearance. These lines will later be buried to meet that ...

Get Price

Ground Rules for Grade-Level Decks | Professional Deck Builder

Leaves and other debris that collect under decks reduce lumber’s drying potential so there’s greater risk of decay in grade-level deck framing than on an elevated deck. It’s only been in the last year that my local lumberyards and big-box stores began stocking ground-contact treated dimensional lumber; before that I had to special-order ...

Get Price

Recommended Beam & Joist Spans for Deck Framing | Home Guides ...

The dimensions of the framing the type of wood the framing is made from the design of the deck and the weight load on the structure determine the maximum span distances for joists and beams and ...

Get Price

Span Tables for deck joists deck beams and deck flooring ...

Framing tables for decks: joist & beam spans & sizes. Recommended or allowable joist & beam spans: this article explains typical spans for deck joists deck beams and deck flooring giving both standard span tables and a quick "rule of thumb" that works pretty well.

Get Price

Deck Framing - mycarpentry.com

To maximize the use of the deck material (10') and to minimize waste on the 10 x 10 (3048 x 3048 mm) deck project the finished width of the deck framing will be 9' 6" (2896 mm). The decking material will be 9' 9" (2972 mm) (with a 1.5 inch (38 mm) overhang on the two sides and front of the deck).

Get Price

What Size Screws to Use for Decking Boards Frame Railings?

For deck framing structural wood screws such as Simpson SDS 1.5” screws work with joist and stringer hangers as well as post/beam brackets. Railing posts require ½” diameter galvanized or stainless steel through bolts while railings will need 3.5” coated deck screws for balusters and rails.

Get Price

Sizing Posts | Professional Deck Builder

For taller decks with 2x10 framing I might question 4x4 posts. Using the same methodology with 2x12 framing I'd allow 4x4 posts at heights of about 4 feet for southern pine or Douglas fir before asking questions. Of course that assumes the joist and beam sizes were based on maximum spans not overbuilding.

Get Price

Deck Joist Span Chart - Fine Homebuilding

But the 2015 IRC included a new one (Table R507.5) that will make it easy for deck builders to spec a joist size for a given span and joist spacing. The table includes spans for common lumber species used for deck framing like southern pine Douglas fir hem-fir redwood western cedar and other species.

Get Price

Learn how to frame a deck how to build a deck frame and the ...

Deck boards will be attached to the deck frame by connecting directly to the joist by face-fastening via Deck Screws in a concealed face-fastening method via a Pro Plug System or in a nearly invisible manner with a Hidden Deck Fastener system. Popular decking material includes natural or pressure-treated lumber composite decking such as Seven Trust ...

Get Price

Screws vs. Nails: Which Is Better for Framing Deck Fence ...

In either case before deciding on whether to use screws or nails – and even what size to use – for a major framing project consult the local regulations. Screws vs. Nails Building a Deck. If you are planning to build yourself a wood deck you have three options – use only screws only nails or a mix of both.

Get Price

How Much Wood Do I Need for a 12x12 Porch? | Hunker

The most accurate way to determine the amount of wood you will need for the frame materials is to refer to your detailed plans. You will need a 2-by-10-inch ledger board if you are attaching the deck to the house. Posts are usually constructed from 4-by-4-inch or 6-by-6-inch posts and you will need at least five.

Get Price

Product Details

Product List